TWO MULTI-OBJECTIVE APPROACHES TOOPTIMIZETHECOMPOSITION AND PROPERTIES OF ALLOY STEELS

Nikolay Tontchev

Scientific paper ID 834 : 2013/3

TWO MULTI-OBJECTIVE APPROACHES TOOPTIMIZETHECOMPOSITION AND PROPERTIES OF ALLOY STEELS

Nikolay Tontchev

The article is dedicated to two approaches optimizing a task of statistical modeling of the mechanical properties of products in real production metallurgy process. The approachesare designed for the benefit of producers-metallurgists aimed at providing panels of steels of a specific set of eventual industrial properties. This is accomplished by some procedures of composition optimizing based on existing certificates of brands alloy steels. Since the composition of alloys is searched in accordance with the previously announced ments, it results in a system of limitations, and the task is formulated as a task of decision support.

• Reload article • Open/Download as PDF

високояки стомани моделиране многокритериална оптимизацияAHSS steels modeling MCDMNikolay Tontchev

BIBLIOGRAPHY

[1] Matlock K.D., J.G. Speer at all, Recent Developments in Advanced High Strength Sheet Steels for automotive application: an overview, JESTECH, 15 (1), 1-12, (2012).

[2] MilitzerM., S. Sarkar, K. Mukherjee, H. Azizi-Alizamini and W.J. Poole, “Advanced Steels with Complex Ultra-Fine Grained Microstructures,” Proc. of New Developments on Metallurgy and Applications of High Strength Steels, Buenos Aires, ed. T. Perez, TMS, May 26-28, 2008.

[3]MatsumuraO., Y. Sakuma, Y. Ishii and J. Zhao, “Effect of Retained Austenite on Formability of High Strength Sheet Steels,” ISIJ Intl., Vol. 32, No. 10, 1992, pp. 1110-1116.

[4] PerrardF. , C. Scott, “Vanadium Precipitation During Intercritical Annealing in Cold Rolled TRIP Steels,” ISIJ Intl., Vol. 47, No. 8, 2007, pp. 1168-1177.

[5] MoorE. , J. Penning, C. Föjer, A.J. Clarke, J.G. Speer, “Alloy Design for Enhanced Austenite Stabilization via Quenching and Partitioning,” Proc. of the Intl. Conf. on New Developments in Advanced High-Strength Sheet Steels , AIST, June 15-18, 2008, Orlando, Fla, pp. 199-207.

[6] Garcia-Mateo C., F.G. Caballero, “Ultra-high-strength Bainitic Steels,” ISIJ Intl., Vol. 45, No. 11, 2005, pp. 1736-1740.

[7] SpeerJ. G., E. De Moor, K. O. Findley, D. K. Matlock, B. C. De Cooman, and D. V. Edmonds, “Analysis of Microstructure Evolution in Quenching and Partitioning Automotive Sheet Steel,” Metallurgical and Materials Transactions A, vol. 42, no. 12, 2011, pp. 3591-3601.

[8] VercammenS., B. Blanpain, B.C. De Cooman and P. Wollants, “Cold rolling behavior of an austenitic Fe-30Mn-3Al-3Si TWIP-steel: the importance of deformation twinning,” Acta Mat., Vol. 52, Issue 7, 2004, pp. 2005-2012.

[9]BrackeL., G. Mertens, J. Penning, B.C. De Cooman, M. Liebherr and N. Akdut, “Influence of Phase Transformations on the Mechanical Properties of High-Strength Austenitic Fe-Mn-Cr Steel,” Metall. Trans. A, Vol. 37A, 2006, pp. 307-317.

[10]MerwinM.J., Microstructure and Properties of Cold-Rolled-and-Annealed Low-Carbon Ma-nganese TRIP Steels, Proc. ofMaterials Science and Technology 2007, Sept. 16-20, 2007, Detroit, MI, pp. 515-536.

[11]Tontchev N., Y. Kalev Determining influence of alloying elements on properties of alloys by robust experiment, MEST Journal, Vol.1, №1, 2013, http://mest.meste.org/MEST_Najava/II_tont-c...

[12] KhosrowDehnad, Qualitty control., Robust design and the Taguchi method, AT&T, 1989.

[13] Bunday B.D., Basic optimization methods, Edward Arnold, 1984.

[14] Ivanov M., Metod za otsenka na riskovite faktori pri razrabotvaneto na softuerni produkti, Parva mezhdunarodna nauchna konferentsiya „E-upravlenie”, 22-24 yuni 2009, Sozopol.
( [14] Иванов М., Метод за оценка на рисковите фактори при разработването на софтуерни продукти, Първа международна научна конференция „Е-управление”, 22-24 юни 2009, Созопол. )

[15] Ivanov M.P., I.Momchev, Printsipi i problemi na mnogokriterialnata otsenka na kachestvoto na softuerniya produkt, sp.”Avtomatika i informatika”, 2006.
( [15] Иванов М.П., И.Момчев, Принципи и проблеми на многокритериалната оценка на качеството на софтуерния продукт, сп.”Автоматика и информатика”, 2006. )